Register map(s) for this device, with a note of how far each has been checked. Addresses are 0-based, as on the wire. Scale and byte order are confirmed only at the hardware-verified rung.
Round-trips through a real Modbus stack with no overlapping addresses and a word-order-sensitive codec — the map is internally coherent and wire-decodable. Does NOT prove byte-order or scaling match a real device: the emulator is seeded from the map's own types, so a uniformly wrong byte-order still round-trips. Only hardware-verified confirms byte-order/scale on the wire.
| point | address (0-based) | type | scale | unit |
|---|---|---|---|---|
| voltage_u1 | 2499 | F32BE | 1 | |
| voltage_u2 | 2501 | F32BE | 1 | |
| voltage_u3 | 2503 | F32BE | 1 | |
| voltage_uavg_ln | 2505 | F32BE | 1 | |
| voltage_u12 | 2507 | F32BE | 1 | |
| voltage_u23 | 2509 | F32BE | 1 | |
| voltage_u31 | 2511 | F32BE | 1 | |
| voltage_uavg_ll | 2513 | F32BE | 1 | |
| current_i1 | 2515 | F32BE | 1 | |
| current_i2 | 2517 | F32BE | 1 | |
| current_i3 | 2519 | F32BE | 1 | |
| current_neutral_calculated | 2523 | F32BE | 1 | |
| frequency | 2583 | F32BE | 1 | |
| active_power_l1 | 2529 | F32BE | 1 | |
| active_power_l2 | 2531 | F32BE | 1 | |
| active_power_l3 | 2533 | F32BE | 1 | |
| active_power_total | 2535 | F32BE | 1 | |
| reactive_power_l1 | 2537 | F32BE | 1 | |
| reactive_power_l2 | 2539 | F32BE | 1 | |
| reactive_power_l3 | 2541 | F32BE | 1 | |
| reactive_power_total | 2543 | F32BE | 1 | |
| apparent_power_l1 | 2545 | F32BE | 1 | |
| apparent_power_l2 | 2547 | F32BE | 1 | |
| apparent_power_l3 | 2549 | F32BE | 1 | |
| apparent_power_total | 2551 | F32BE | 1 | |
| power_factor_l1 | 2561 | F32BE | 1 | |
| power_factor_l2 | 2563 | F32BE | 1 | |
| power_factor_l3 | 2565 | F32BE | 1 | |
| power_factor_total | 2567 | F32BE | 1 | |
| energy_counter_1 | 2603 | F32BE | 1 | |
| energy_counter_2 | 2605 | F32BE | 1 | W |
| energy_counter_3 | 2607 | F32BE | 1 | W |
| energy_counter_4 | 2609 | F32BE | 1 | var |
⚠ Service USB communication is not galvanic separated! When using service USB communication, power supply and measuring voltages need to be disconnected! — Starkest reads only; we never write a control register.
| terminals | Screw terminals for RS232, RS485, and M-Bus. USB standard Type B for USB. Mini-B for Service USB. DSUB 9-pin female for Profibus. |
| isolation | RS232/RS485 in accordance with EN 61010-1 standard. Service USB is not galvanic insulated. Profibus and M-Bus are galvanic insulated. |
| power | Adaptable power supply. Universal power supply: 20...300 V DC / 48...276 V AC. AC power supply: 230, 240 V AC. Consumption < 5 VA. |
| environment | Operating temperature: -10 to +60°C. Storage temperature: -40 to +70°C. Max humidity: <= 75% r.h. |
| accuracy | Analogue output accuracy: 0.5% of range. Class 0.5. |
| certifications | Safety: EN 61010-1, EMC: 2014/30/EU, EN 61326-1, Protection: EN 60529 (Front: IP52, Rear: IP20) |
| doc revision | February 2017 • Version 8.00 |
⚠ disputed: voltage_u1 @ 2499 — disputed by Iskra/DEIF Modbus map which lists U1 starting at 2500 (PLC 302501)
⚠ disputed: current_i1 @ 2515 — disputed by Iskra/DEIF Modbus map which lists I1 starting at 2516 (PLC 302517)
⚠ disputed: frequency @ 2583 — disputed by Iskra/DEIF Modbus map which lists Frequency at 2584 (PLC 302585) or 2498 (PLC 302499)
⚠ disputed: energy_counter_1 @ 2603 — disputed by Iskra MC3x0x Modbus map which lists Counter E1 at 30406 (Modbus 405)
Each rung states what it proved and what it did not. Gray until proven; green is earned by hardware only.
Device not here? Upload its manual and get a checked map back. It's free.
Want it confirmed against your own device? Order hardware verification. If it doesn't check out, you don't pay.
Building on a lot of devices? License the library — machine-readable maps, the firmware matrix, and API access.