Register map(s) for this device, with a note of how far each has been checked. Addresses are 0-based, as on the wire. Scale and byte order are confirmed only at the hardware-verified rung.
Round-trips through a real Modbus stack with no overlapping addresses and a word-order-sensitive codec — the map is internally coherent and wire-decodable. Does NOT prove byte-order or scaling match a real device: the emulator is seeded from the map's own types, so a uniformly wrong byte-order still round-trips. Only hardware-verified confirms byte-order/scale on the wire.
| point | address (0-based) | type | scale | unit |
|---|---|---|---|---|
| states_alarms_1 | 0 | U16 | 1 | |
| states_alarms_2 | 1 | U16 | 1 | |
| states_alarms_3 | 2 | U16 | 1 | |
| states_alarms_4 | 3 | U16 | 1 | |
| input_voltage_v1 | 11 | U16 | 1 | V |
| input_voltage_v2 | 12 | U16 | 1 | V |
| input_voltage_v3 | 13 | U16 | 1 | V |
| input_frequency | 17 | U16 | 0.1 | Hz/10 |
| bypass_voltage_v1 | 21 | U16 | 1 | V |
| bypass_voltage_v2 | 22 | U16 | 1 | V |
| bypass_voltage_v3 | 23 | U16 | 1 | V |
| bypass_frequency | 24 | U16 | 0.1 | Hz/10 |
| output_voltage_v1 | 25 | U16 | 1 | V |
| output_voltage_v2 | 26 | U16 | 1 | V |
| output_voltage_v3 | 27 | U16 | 1 | V |
| load_phase_l1 | 37 | U16 | 1 | % |
| load_phase_l2 | 38 | U16 | 1 | % |
| load_phase_l3 | 39 | U16 | 1 | % |
| output_frequency | 43 | U16 | 0.1 | Hz/10 |
| battery_voltage | 47 | U16 | 0.1 | V/10 |
| charge_percent | 51 | U16 | 1 | % |
| autonomy | 53 | U16 | 1 | Minutes |
| internal_ups_temperature | 61 | I16 | 1 | °C |
| output_nominal_voltage | 77 | U16 | 1 | V |
| output_nominal_frequency | 78 | U16 | 0.1 | Hz/10 |
| output_nominal_power_kva | 79 | U16 | 0.1 | kVA/10 |
| output_nominal_power_kw | 80 | U16 | 0.1 | kW/10 |
| battery_nominal_capacity | 83 | U16 | 1 | Ah |
| battery_benches | 84 | U16 | 1 | 1 or 2 |
| counter_correct_messages | 118 | U16 | 1 | Integer |
| counter_incorrect_messages | 119 | U16 | 1 | Integer |
| firmware_version | 128 | U16 | 0.01 | Integer*100 |
| terminals | DB9 for SERIAL 1, RJ45 for SERIAL 2 |
| termination | Embedded terminal resistor for RS485 bus (Rt=120Ω) enabled via DIP-switch no. 6 |
| connector | DB9 and RJ45 |
| wiring notes | SERIAL 2 port can be set as RS-485 Half Duplex port (default) or as RS-232 port by setting jumpers JP10, JP11, JP12 and JP13 |
| sentinel values | For single-phase systems, the value 0xFFFF is reported in the registers relating to L2 and L3. |
| protocol notes | Slave Address = Base Address + [DIP-switch configuration] |
| firmware register | 128 |
| identification notes | Firmware version is reported in register 129 (address 128) as Integer*100 |
| environment | Closed environments only |
| doc revision | 0MNACCMC2ENUG |
Each rung states what it proved and what it did not. Gray until proven; green is earned by hardware only.
Device not here? Upload its manual and get a checked map back. It's free.
Want it confirmed against your own device? Order hardware verification. If it doesn't check out, you don't pay.
Building on a lot of devices? License the library — machine-readable maps, the firmware matrix, and API access.