Yaskawa V1000 drive (MEMOBUS/Modbus)

Register map(s) for this device, with a note of how far each has been checked. Addresses are 0-based, as on the wire. Scale and byte order are confirmed only at the hardware-verified rung.

coherence-checked

Round-trips through a real Modbus stack with no overlapping addresses and a word-order-sensitive codec — the map is internally coherent and wire-decodable. Does NOT prove byte-order or scaling match a real device: the emulator is seeded from the map's own types, so a uniformly wrong byte-order still round-trips. Only hardware-verified confirms byte-order/scale on the wire.

point	address (0-based)	type	scale	unit
drive_status_1	32	U16	1
fault_contents_1	33	U16	1
data_link_status	34	U16	1
frequency_reference	35	U16	0.01	Hz
output_frequency	36	U16	0.01	Hz
output_voltage_reference	37	U16	0.1	V
output_current	38	U16	0.01	A
output_power	39	U16	0.1	kW
torque_reference	40	I16	0.1	%
fault_contents_2	41	U16	1
alarm_contents_1	42	U16	1
input_terminal_status	43	U16	1
drive_status_2	44	U16	1
output_terminal_status	45	U16	1
frequency_reference_bias	47	I16	0.1	%
dc_bus_voltage	49	U16	1	V
torque_monitor	50	I16	1	%
pid_feedback	56	U16	0.1	%
pid_input	57	I16	0.1	%
pid_output	58	I16	0.1	%
output_frequency_rpm	62	U16	1	r/min
output_frequency_percent	63	U16	0.01	%
drive_status	75	U16	1
cumulative_operation_time_10h	152	U16	10	h
cumulative_operation_time_1h	153	U16	1
cooling_fan_operation_time_10h	154	U16	10	h
cooling_fan_operation_time_1h	155	U16	1
drive_rated_current	171	U16	0.01	A
motor_speed	172	U16	1

link settings as documented (unverified): RTU; default 9600 8N1; unit ID 31; FC 03,08,16; MEMOBUS/Modbus (using RTU mode only)

bench facts as documented (unverified)

terminals	R+, R-, S+, S-, IG
termination	Built-in terminating resistance enabled/disabled via DIP switch S2
connector	Removable terminal block
max registers/read	16
response timeout	2000 ms
broadcast	supported
model register	52
power	200 V Class, Three-Phase Input: 0.1 to 18.5 kW; 200 V Class, Single-Phase Input: 0.1 to 3.7 kW; 400 V Class, Three-Phase Input: 0.2 to 18.5 kW
environment	Ambient Temperature: IP20/NEMA Type 1: -10 to +40 °C, IP20/IP00 Open-Chassis: -10 to +50 °C. Humidity: 95% RH or less. Altitude: Up to 1000 m without derating.
doc revision	SIEP C710606 16D

The trust ladder

Each rung states what it proved and what it did not. Gray until proven; green is earned by hardware only.

generated — A prompt produced it. Unproven — anyone can regenerate this.
structure-verified — Decode path is structurally sound (addresses, widths, finite values). Does NOT prove word order or scaling.
coherence-checked — Round-trips through a real Modbus stack with no overlapping addresses and a word-order-sensitive codec — the map is internally coherent and wire-decodable. Does NOT prove byte-order or scaling match a real device: the emulator is seeded from the map's own types, so a uniformly wrong byte-order still round-trips. Only hardware-verified confirms byte-order/scale on the wire.
hardware-verified (software-key) x1 — Matched a real device with operator-attested readings as ground truth — the only rung that confirms word order + scaling on the wire.

Device not here? Upload its manual and get a checked map back. It's free.

Want it confirmed against your own device? Order hardware verification. If it doesn't check out, you don't pay.

Building on a lot of devices? License the library — machine-readable maps, the firmware matrix, and API access.