Register map(s) for this device, each at the trust rung it earned. Addresses are 0-based as on the wire. Word order and scaling are confirmed at the hardware-verified rung and at no rung below it.
Read + decoded cleanly over a real network vs an independent third-party Modbus test server (transport and framing; reads are remapped into the server's register window, so the map's own addresses are NOT exercised). Does NOT prove word order/scaling against the actual device.
| point | address (0-based) | type | scale | unit |
|---|---|---|---|---|
| user_value_percent | 0 | F32BE | 1 | % |
| pressure_sensor_1 | 2 | F32BE | 1 | Pressure unit |
| pressure_sensor_2 | 4 | F32BE | 1 | Pressure unit |
| temperature_sensor_1 | 6 | F32BE | 1 | °C |
| cpu_temperature | 8 | F32BE | 1 | °C |
| temperature_sensor_2 | 10 | F32BE | 1 | °C |
| user_value_percent_int | 16 | I16 | 0.01 | % |
| pressure_sensor_1_int | 17 | I16 | 0.01 | Pressure unit |
| pressure_sensor_2_int | 18 | I16 | 0.01 | Pressure unit |
| temperature_sensor_1_int | 19 | I16 | 0.01 | °C |
| cpu_temperature_int | 20 | I16 | 0.01 | °C |
| temperature_sensor_2_int | 21 | I16 | 0.01 | °C |
| pressure_unit | 22 | U16 | 1 | |
| upper_sensor_limit | 24 | F32BE | 1 | Pressure unit |
| lower_sensor_limit | 26 | F32BE | 1 | Pressure unit |
| damping_value | 28 | F32BE | 1 | s |
| response_delay_value | 30 | U16 | 1 | ms |
| modbus_address | 31 | U16 | 1 | |
| status_register | 35 | U16 | 1 |
⚠ Warning to proceed strictly in accordance with the information contained in the documentation in order to ensure the safety and full functionality of the device. — Starkest reads only; we never write a control register.
| terminals | Internal electrical switching terminals suitable for conductors with cross-section from 0.5 to 2.5 mm2 |
| A/B polarity | PM12: 2 (+), 3 (-/GND), 4 (A+), 5 (B-). PKD/SG: Red (+), Black (-), Blue (A+), Yellow (B-). PZ: 1 (+), 2 (-), 4 (A+), 3 (B-). |
| termination | Not integrated with termination resistors as standard. PCE-28.Modbus16 and PRE-28.Modbus16 with PZ/PZ4 have a 560 ohm resistor switchable via DIP switch. |
| connector | PM12, PKD, SG, PZ, PZ4 |
| isolation | No galvanic isolation; common voltage level should be equalized by connecting negative poles together. |
| shield/ground | Connect screen on one side at the transmitter's power supply point. |
| response timeout | 5 ms |
| broadcast | supported |
| protocol notes | Silent interval between characters must not exceed 1.5T. Silent interval before response must not be shorter than 3.5T. |
| model register | 0x0020 |
| serial register | 0x0020 |
| firmware register | Software revision in configuration mode |
| FC 43 device ID | supported |
| power | Modbus standard: 4-28 V DC. Configuration standard: 5-28 V DC. Exi version: 4-10 V DC or 10.5-15.8 V DC depending on model. Current < 3.6 mA to < 24 mA. |
| environment | Avoid mechanical impacts, excessive shocks/vibration, excessive temperature fluctuation, water vapor condensation, dusting, icing. Min ambient temperature -40°C (-50°C special version). |
| accuracy | Indication error: 0.2% +/- 1 digit |
| certifications | ATEX, IECEx, CE |
| doc revision | Revision 03.A.001 |
| firmware applicability | Version 18 of the transmitter firmware |
Each rung states what it proved and what it did not. Gray until proven; green is earned by hardware only.
If your device isn't here, upload its register map. Generation is free, and the connector keeps the rung it earns under testing.
To prove a connector against your own device, order hardware verification. If it doesn't verify, you don't pay.
Platform builders can license the verified library: machine-readable maps, the firmware matrix, API access.