Register map(s) for this device, each at the trust rung it earned. Addresses are 0-based as on the wire. Word order and scaling are confirmed at the hardware-verified rung and at no rung below it.
Read + decoded cleanly over a real network vs an independent third-party Modbus test server (transport and framing; reads are remapped into the server's register window, so the map's own addresses are NOT exercised). Does NOT prove word order/scaling against the actual device.
| point | address (0-based) | type | scale | unit |
|---|---|---|---|---|
| process_value | 4096 | I16 | 0.1 | 0.1 °C/°F |
| set_point | 4097 | I16 | 0.1 | 0.1 °C/°F |
| upper_limit_temperature_range | 4098 | I16 | 0.1 | °C/°F |
| lower_limit_temperature_range | 4099 | I16 | 0.1 | °C/°F |
| input_temperature_sensor_type | 4100 | U16 | 1 | |
| control_method | 4101 | U16 | 1 | |
| heating_cooling_control_selection | 4102 | U16 | 1 | |
| proportional_band | 4105 | U16 | 0.1 | |
| integral_time | 4106 | U16 | 1 | s |
| derivative_time | 4107 | U16 | 1 | s |
| coef_dual_loop | 4110 | U16 | 0.01 | |
| dead_band_dual_loop | 4111 | I16 | 1 | |
| hysteresis_output_1 | 4112 | U16 | 1 | |
| hysteresis_output_2 | 4113 | U16 | 1 | |
| output_value_1 | 4114 | U16 | 0.1 | % |
| output_value_2 | 4115 | U16 | 0.1 | % |
| temperature_regulation_value | 4118 | I16 | 0.1 | 0.1 °C/°F |
| alarm_1_type | 4128 | U16 | 1 | |
| alarm_2_type | 4129 | U16 | 1 | |
| alarm_3_type | 4130 | U16 | 1 | |
| upper_limit_alarm_1 | 4132 | I16 | 0.1 | |
| lower_limit_alarm_1 | 4133 | I16 | 0.1 | |
| upper_limit_alarm_2 | 4134 | I16 | 0.1 | |
| lower_limit_alarm_2 | 4135 | I16 | 0.1 | |
| upper_limit_alarm_3 | 4136 | I16 | 0.1 | |
| lower_limit_alarm_3 | 4137 | I16 | 0.1 | |
| read_led_status | 4138 | U16 | 1 | |
| read_push_button_status | 4139 | U16 | 1 |
⚠ Erasing the user entered values may result in a safety hazard and system malfunction. — Starkest reads only; we never write a control register.
| terminals | Fork terminals with isolation (M3 screw, width is 7.0mm (6.0mm for 32B Series), hole diameter 3.2mm) |
| A/B polarity | Make sure all wires are connected to the correct polarity of terminals |
| connector | Screw terminals |
| isolation | DOUBLE INSULATION or REINFORCED INSULATION (equivalent to Class II of IEC 536) |
| shield/ground | SG (Signal Ground) terminal |
| max registers/read | 8 |
| protocol notes | 03H to read the contents of register (Max. 8 words). 02H to read the bits data (Max. 16 bits). |
| firmware register | 4143 |
| power | 100 to 240 VAC 50/60 Hz OR 24 VDC (depending on model), 5VA max |
| environment | Ambient Temperature: 32°F to 122°F (0°C to +50°C), Storage Temperature: -4°F to 150°F (-20°C to +65°C), Relative Humidity: 35% to 80% (non-condensing), Altitude: 2000 m or less |
| accuracy | Display Accuracy: 0 or 1 digit to the right of the decimal point (selectable). Current transformer accuracy: ±0.5 Amps |
| certifications | Class II of IEC 536 |
| doc revision | FR# R5-443601-10 Rev. 5 |
Each rung states what it proved and what it did not. Gray until proven; green is earned by hardware only.
If your device isn't here, upload its register map. Generation is free, and the connector keeps the rung it earns under testing.
To prove a connector against your own device, order hardware verification. If it doesn't verify, you don't pay.
Platform builders can license the verified library: machine-readable maps, the firmware matrix, API access.