Register map(s) for this device, each at the trust rung it earned. Addresses are 0-based as on the wire. Word order and scaling are confirmed at the hardware-verified rung and at no rung below it.
Read + decoded cleanly over a real network vs an independent third-party Modbus test server (transport and framing; reads are remapped into the server's register window, so the map's own addresses are NOT exercised). Does NOT prove word order/scaling against the actual device.
| point | address (0-based) | type | scale | unit |
|---|---|---|---|---|
| motor_status | 512 | U16 | 1 | |
| motor_thermal_capacity_used | 513 | U16 | 1 | % |
| estimated_time_to_trip_on_overload | 514 | I16 | 1 | s |
| restart_attempts | 515 | U16 | 1 | |
| restart_total_delay | 516 | U16 | 1 | sec. |
| restart_in_progress | 517 | U16 | 1 | |
| uvr_power_loss_time | 518 | U16 | 0.1 | 0.1 s |
| motor_speed_status | 519 | U16 | 1 | |
| cause_of_last_trip | 544 | U16 | 1 | |
| phase_a_pre_trip_current | 550 | U16 | 1 | A |
| phase_b_pre_trip_current | 552 | U16 | 1 | A |
| phase_c_pre_trip_current | 554 | U16 | 1 | A |
| motor_load_pre_trip | 556 | U16 | 0.01 | FLA |
| current_unbalance_pre_trip | 557 | U16 | 1 | % |
| ground_current_pre_trip | 558 | U16 | 0.1 | A |
| phase_a_current | 768 | U16 | 1 | |
| phase_b_current | 770 | U16 | 1 | |
| phase_c_current | 772 | U16 | 1 | |
| average_phase_current | 774 | U16 | 1 | |
| motor_load | 776 | U16 | 0.01 | |
| current_unbalance | 777 | U16 | 1 | |
| unbalanced_biased_motor_load | 778 | U16 | 0.01 | |
| ground_current | 779 | U16 | 0.1 | |
| overall_hottest_stator_rtd_owner | 796 | U16 | 1 | |
| overall_hottest_stator_rtd_number | 797 | U16 | 1 | |
| overall_hottest_stator_rtd_temperature | 798 | I16 | 1 | |
| local_hottest_stator_rtd_number | 799 | U16 | 1 | |
| local_hottest_stator_rtd_temperature | 800 | I16 | 1 | |
| local_rtd_1_temperature | 801 | I16 | 1 | |
| local_rtd_2_temperature | 802 | I16 | 1 | |
| local_rtd_3_temperature | 803 | I16 | 1 | |
| local_rtd_4_temperature | 804 | I16 | 1 | |
| local_rtd_5_temperature | 805 | I16 | 1 | |
| local_rtd_6_temperature | 806 | I16 | 1 | |
| local_rtd_7_temperature | 807 | I16 | 1 | |
| local_rtd_8_temperature | 808 | I16 | 1 | |
| local_rtd_9_temperature | 809 | I16 | 1 | |
| local_rtd_10_temperature | 810 | I16 | 1 | |
| local_rtd_11_temperature | 811 | I16 | 1 | |
| local_rtd_12_temperature | 812 | I16 | 1 | |
| vab | 864 | U16 | 1 | |
| vbc | 865 | U16 | 1 | |
| vca | 866 | U16 | 1 | |
| average_line_voltage | 867 | U16 | 1 | |
| van | 868 | U16 | 1 | |
| vbn | 869 | U16 | 1 | |
| vcn | 870 | U16 | 1 | |
| average_phase_voltage | 871 | U16 | 1 | |
| system_frequency | 872 | U16 | 0.01 | |
| power_factor | 880 | I16 | 0.01 | |
| real_power | 881 | I16 | 1 | |
| real_power_hp | 883 | U16 | 1 | |
| reactive_power | 884 | I16 | 1 | |
| apparent_power | 886 | U16 | 1 | |
| positive_megawatthours | 887 | U16 | 1 | |
| positive_megavarhours | 889 | U16 | 1 | |
| negative_megavarhours | 891 | U16 | 1 | |
| positive_kilowatthours | 893 | U16 | 1 | |
| positive_kilovarhours | 895 | U16 | 1 | |
| negative_kilovarhours | 897 | U16 | 1 | |
| current_demand | 912 | U16 | 1 | |
| real_power_demand | 914 | U16 | 1 | |
| reactive_power_demand | 916 | U16 | 1 | |
| apparent_power_demand | 918 | U16 | 1 | |
| peak_current_demand | 919 | U16 | 1 | |
| peak_real_power_demand | 921 | U16 | 1 | |
| peak_reactive_power_demand | 923 | U16 | 1 | |
| peak_apparent_power_demand | 925 | U16 | 1 | |
| number_of_motor_starts | 1136 | U16 | 1 | |
| number_of_emergency_restarts | 1137 | U16 | 1 | |
| motor_running_hours | 1184 | U16 | 1 |
| terminals | one of three 2-wire RS485 ports from the rear terminal connector, the RS232 from the front panel connector, a fibre optic connection |
| A/B polarity | Each '+' terminal of every 369 must be connected together for the system to operate. |
| termination | The terminating network should consist of a 120 ohm resistor in series with a 1 nF ceramic capacitor when used with Belden 9841 RS485 wire. |
| connector | rear terminal connector, front panel connector, RJ45 connector |
| shield/ground | Shielded wire should always be used to minimize noise. |
| max registers/read | 125 |
| inter-frame delay | 3 ms |
| broadcast | supported |
| model register | 0x0000 |
| serial register | 0x0020 |
| firmware register | 0x0002 |
| certifications | CE, UL, ISO9001:2000 |
| doc revision | 3.4x |
Each rung states what it proved and what it did not. Gray until proven; green is earned by hardware only.
If your device isn't here, upload its register map. Generation is free, and the connector keeps the rung it earns under testing.
To prove a connector against your own device, order hardware verification. If it doesn't verify, you don't pay.
Platform builders can license the verified library: machine-readable maps, the firmware matrix, API access.